HID KITS' lights of note
HID lights are luminous arc, never broken wires in question.
HID's power consumption only 35 W, its luminescence of the halogen lamp three times, life expectancy is five times the halogen lamp.
HID luminous color and intensity close to sunlight.
Xenon HID headlamps installed
1, testing the lights of the car models in line with this.
2, the original lights removed;
3, removal of the original lines of connection, at the appropriate location to open a hole with a diameter
of 25 mm holes, Xenon lights line for the introduction;
4, apart xenon lamp safety cones;
5, fitted with xenon bulb and clasped, high-tension lines from the opening lead, and then high-tension
lines on the waterproof apron Huzhu openings, to prevent water and dust into the headlamps.
6, Ballast fixed in place;
7, light bulbs connected to power lines and Ballast (butt plugs);
8, connected to 12 V power line and the line of control (as are red, black -0.1);
As long as the lamp with the vehicle in line with the specifications, and there is space to accommodate the stabilizer and the line group, then any vehicle can be installed. Halogen lamp in the base converted Xenon HID headlamps, compared to Ballast placed in ventilation position, to facilitate cooling. Ballast on the Prohibition of the engine, such as fever larger areas. If the temperature reaches 105 degrees, will automatically cut off power supply.
When the attention of the installation to install grounding line, if the grounding of the ground situation bad, xenon Lantern Festival-a time when the dark phenomenon. Battery time is too long, the voltage will be instability, and amounted to less than 10 V, the stabilizer automatically cut off the circuit, xenon lights will be extinguished, the voltage instability will directly affect the use of xenon lamps.
Please note that installed HID lighting fuses. If the two shared a light fuse, the fuse must use the 25 A-30A. If the two light fuses were used independently, must use the 10 A-15A. To pay special attention to the installation of power is extremely negative and grounding. If the car special specifications, such as cathode grounding.
Attention
1, careful! High-pressure dangerous! Could lead to electric shocks hurt!
2, the power switch the lights, please do not contact the lamp to prevent the release of a large number
of calories burned.
3, do not look directly at lights, to prevent eye injuries.
4, automobile accidents when the power is switched off, the damaged high-voltage boxes,
high-voltage cable will be leaked, would be very dangerous.
5, under any circumstances, do not carry out the dismantling and transformation,
we will not bear any responsibility.
6, the need to replace and repair, recently invited to the professional organizations for help.
7, please note that not close to flammable materials such as paper, oil, spray, spray paint, thinners, etc..
8, please do not increase the optical power, would seriously affect the safety of other drivers driving.
9, in the launch vehicle, then opened the lights.
Operation of attention
1, in order to install safety, please wait for the car and engine cooling completely.
2, before installation, make sure that the gear in neutral gear (or parking location).
3, please ensure that the switch closed at the time of installation.
4, was careful not to burn, especially when the lights are switched.
5, careful not to scratch with setbacks and light bulbs, do not touch bulb with your fingers,
will cause stains.
6, carefully testing the connector, client interface, the wire connections. The link will lead to the wrong
lighting problems.
7, the adjustment of light bulbs, do not let the end come into contact with the lamp assembly of the
headlamps in the Hood.
8, in the headlamps of resin or rubber stamp after the drilling of 25 mm holes.
9, connecting the lamp and high pressure starter, will not anyway to negative.
10, connecting stabilizer and power, not negative since then.
How to install light bulbs and Ballasts
1, use double-sided adhesive positioning Ballasts and used screws firmly fixed. On both sides to
ensure solid.
2, I should be grateful if the original Halogen Lamps interface and power interface connector.
(Red to +, and then -).
After installation inspections
1, no confirmation is received anti-negative.
2, no confirmed link is too loose or too tight, not squeeze
Rehabilitation and operation of
1, in order to ensure the installation and opening of components to be assembled in situ;
2, check whether the distance light work;
3, please check the other vehicle parts (lamps, car audio, etc.) is working.
